Scioly.org

Airco2020 wrote:

ScottMaurer19 wrote: I interpreted it as needing to move 20cm within the box itself. Otherwise it cannot become the highest point AFTER 20cm. It would be the highest point before moving a full 20cm and therefore not count for points (nor technically stop the run time unless it somehow didn't raise 20cm before reaching the top due to some unintentional device failure such as a lever accidentally leaving the top dimension and increasing where the top dimension of the device is).

I'm not sure I understand what you mean. My device moves a total of 21cm. It's currently set up to move about 15 in the box and then about 6 above the box so it's the highest point. The judges didn't give any points for the final action since it didn't move 20cm Before becoming the highest point. So my solution is I need to find a way to lower my platform so it can move 20cm in the box and then that final 1cm travel I have needs to be above the box. Or I need to find a new solution that travels more the 21cm.

ScottMaurer19 wrote:

Airco2020 wrote:

ScottMaurer19 wrote: I interpreted it as needing to move 20cm within the box itself. Otherwise it cannot become the highest point AFTER 20cm. It would be the highest point before moving a full 20cm and therefore not count for points (nor technically stop the run time unless it somehow didn't raise 20cm before reaching the top due to some unintentional device failure such as a lever accidentally leaving the top dimension and increasing where the top dimension of the device is).

I'm not sure I understand what you mean. My device moves a total of 21cm. It's currently set up to move about 15 in the box and then about 6 above the box so it's the highest point. The judges didn't give any points for the final action since it didn't move 20cm Before becoming the highest point. So my solution is I need to find a way to lower my platform so it can move 20cm in the box and then that final 1cm travel I have needs to be above the box. Or I need to find a new solution that travels more the 21cm.

Your platform (IMO) needs to move at least 20cm within the measured "box" before becoming the highest point. It doesn't matter if it moves 50 cm in total or 21 cm in total as long as the platform moves 20 vertical cm within the measured device dimensions.

Airco2020 wrote:

ScottMaurer19 wrote: I interpreted it as needing to move 20cm within the box itself. Otherwise it cannot become the highest point AFTER 20cm. It would be the highest point before moving a full 20cm and therefore not count for points (nor technically stop the run time unless it somehow didn't raise 20cm before reaching the top due to some unintentional device failure such as a lever accidentally leaving the top dimension and increasing where the top dimension of the device is).

I'm not sure I understand what you mean. My device moves a total of 21cm. It's currently set up to move about 15 in the box and then about 6 above the box so it's the highest point. The judges didn't give any points for the final action since it didn't move 20cm Before becoming the highest point. So my solution is I need to find a way to lower my platform so it can move 20cm in the box and then that final 1cm travel I have needs to be above the box. Or I need to find a new solution that travels more the 21cm.

PM2017 wrote:

Airco2020 wrote:

ScottMaurer19 wrote: I interpreted it as needing to move 20cm within the box itself. Otherwise it cannot become the highest point AFTER 20cm. It would be the highest point before moving a full 20cm and therefore not count for points (nor technically stop the run time unless it somehow didn't raise 20cm before reaching the top due to some unintentional device failure such as a lever accidentally leaving the top dimension and increasing where the top dimension of the device is).

I'm not sure I understand what you mean. My device moves a total of 21cm. It's currently set up to move about 15 in the box and then about 6 above the box so it's the highest point. The judges didn't give any points for the final action since it didn't move 20cm Before becoming the highest point. So my solution is I need to find a way to lower my platform so it can move 20cm in the box and then that final 1cm travel I have needs to be above the box. Or I need to find a new solution that travels more the 21cm.

If you need a fast fix, you could always attach a popsicle stick or something to the frame so that the highest point is ~0.5 cm lower than the highest point of your lift. You would lose ~ 5 points, given the values you told us, but it's a pretty good payoff lol.


EDIT: Unless you're already at 60x60x55 or something, in which case it's probably fairly easy to adjust where your lift is. (IDK why you would be at those dimensions anyways.)

PM2017 wrote:[
If you need a fast fix, you could always attach a popsicle stick or something to the frame so that the highest point is ~0.5 cm lower than the highest point of your lift. You would lose ~ 5 points, given the values you told us, but it's a pretty good payoff lol.


EDIT: Unless you're already at 60x60x55 or something, in which case it's probably fairly easy to adjust where your lift is. (IDK why you would be at those dimensions anyways.)

Airco2020 wrote:

PM2017 wrote:[
If you need a fast fix, you could always attach a popsicle stick or something to the frame so that the highest point is ~0.5 cm lower than the highest point of your lift. You would lose ~ 5 points, given the values you told us, but it's a pretty good payoff lol.


EDIT: Unless you're already at 60x60x55 or something, in which case it's probably fairly easy to adjust where your lift is. (IDK why you would be at those dimensions anyways.)

Great idea. We can put it right next to the platform so there is no confusion that the platform finishes as the highest point. We currently get 76 of the possible 90 points for size so giving up 5 is OK. I don't want to completely redesign an action that works perfectly. I guess the major frustration is that it's been run twice without question including one 1st place and then was completely regected .

diplodocus wrote:Hello all! I have a question regarding the platform. It says it has to be the same dimensions on all sides... does this mean the platform is essentially a cube? Or does the same dimension clause only refer to the top surface of the platform?

CookiePie1 wrote:

diplodocus wrote:Hello all! I have a question regarding the platform. It says it has to be the same dimensions on all sides... does this mean the platform is essentially a cube? Or does the same dimension clause only refer to the top surface of the platform?

Yes, it only refers to the top surface. I used 1 in pine for my platform and haven't had a problem yet.

diplodocus wrote:

CookiePie1 wrote:

diplodocus wrote:Hello all! I have a question regarding the platform. It says it has to be the same dimensions on all sides... does this mean the platform is essentially a cube? Or does the same dimension clause only refer to the top surface of the platform?

Yes, it only refers to the top surface. I used 1 in pine for my platform and haven't had a problem yet.

Thanks for the answer! I was thrown into this event and I have a week to build a functioning machine (and I have no idea what I'm doing lol)... I have another question then. Is there a limit on the height of the platform then? Would 2 inches tall for the platform be too much?